Toyota CORONA FR — TRANSMISSION GEAR (MTM)
33311SHAFT, INPUT
33311ABEARING (FOR INPUT SHAFT FRONT)
33311BRING, SHAFT SNAP (FOR FRONT BEARING)
T=2.35-2.40
T=2.45-2.50
T=2.40-2.45,T=2.40-2.45
T=2.50-2.55
T=2.45-2.50,T=2.55-2.60
T=2.05,MARK 0,T=2.05-2.10
T=2.10,MARK 1,T=2.10-2.15
T=2.15,MARK 2,T=2.15-2.20
T=2.20,MARK 3,T=2.20-2.25
T=2.25,MARK 4,T=2.25-2.30
T=2.30,MARK 5,T=2.30-2.35
T=2.30-2.35,MARK 11,T=2.30-2.35
T=2.35-2.40,MARK 12,T=2.35-2.40
T=2.05,MARK 1,T=2.05-2.10
T=2.10,MARK 2,T=2.10-2.15
T=2.15,MARK 3,T=2.15-2.20
T=2.20,MARK 4,T=2.20-2.25
T=2.25,MARK 5,T=2.25-2.30
33311CRING, HOLE SNAP (FOR NEEDLE ROLLER)
33311DBEARING, INPUT SHAFT
33311GRING, SHAFT SNAP (FOR FRONT BEARING)
33321SHAFT, OUTPUT
33321ABEARING (FOR OUTPUT SHAFT REAR)
33321BRING, SHAFT SNAP (FOR OUTPUT SHAFT BEARING)
T=2.35-2.40,T=2.35-2.40
T=2.40-2.45,T=2.40-2.45
T=2.45-2.50,T=2.45-2.50
T=2.50-2.55,T=2.50-2.55
T=2.55-2.60,T=2.55-2.60
T=2.60-2.65,T=2.60-2.65
T=2.65-2.70,T=2.65-2.70
T=2.68,MARK 14,T=2.68-2.73
T=2.74,MARK 15,T=2.74-2.79
T=2.67-2.72,MARK A,T=2.67-2.72
T=2.73-2.78,MARK B,T=2.73-2.78
T=2.79-2.84,MARK C,T=2.79-2.84
T=2.85-2.90,MARK D,T=2.85-2.90
T=2.91-2.96,MARK E,T=2.91-2.96
T=2.97-3.02,MARK F,T=2.97-3.02
T=3.03-3.08,MARK G,T=3.03-3.08
T=3.09-3.14,MARK H,T=3.09-3.14
T=3.15-3.20,MARK J,T=3.15-3.20
T=3.21-3.26,MARK K,T=3.21-3.26
T=3.27-3.32,MARK L,T=3.27-3.32
T=2.43-2.48,MARK 10,T=2.43-2.48
T=2.49-2.54,MARK 11,T=2.49-2.54
T=2.55-2.60,MARK 12,T=2.55-2.60
T=2.61-2.66,MARK 13,T=2.61-2.66
T=1.89-1.94
T=1.95-2.00
T=2.01-2.06
T=2.07-2.12
T=2.13-2.18
T=2.19-2.24
T=2.25-2.30
T=2.31-2.36,MARK 8,T=2.31-2.36
T=2.37-2.42,MARK 9,T=2.37-2.42
T=0.95-1.05,NO MARK,T=0.95-1.05,NO MARK
33321CRING, SHAFT SNAP (FOR OUTPUT SHAFT BEARING)
T=1.50,OD=31.3
T=1.65,ID=71.1
33331GEAR, REVERSE
33331ABEARING (FOR REVERSE GEAR)
33332GEAR, 2ND
33332BBEARING, NEEDLE ROLLER (FOR 2ND GEAR)
33335GEAR, 1ST
33335CBEARING, NEEDLE ROLLER(FOR 1ST GEAR)
33344BUSH, REVERSE GEAR
33344AKEY OR BALL, REVERSE GEAR BEARING
33361HUB, TRANSMISSION CLUTCH, NO.1
33362HUB, TRANSMISSION CLUTCH, NO.2
33362ARING, SHAFT SNAP (FOR CLUTCH HUB NO.2 SETTING)
T=1.85-1.90,MARK D-1,T=1.85-1.90
T=1.95-2.00,MARK E-1,T=1.95-2.00
T=1.75-1.80,MARK C-1,T=1.75-1.80
T=2.05-2.10,MARK F-1,T=2.05-2.10
T=1.80-1.85,MARK D,T=1.80-1.85
T=1.90-1.95,MARK E,T=1.90-1.95
T=2.00-2.05,MARK F,T=2.00-2.05
33363SLEEVE, TRANSMISSION HUB, NO.1
33364SLEEVE, TRANSMISSION HUB, NO.2
33365KEY, SYNCHROMESH SHIFTING, NO.1
33366KEY, SYNCHROMESH SHIFTING, NO.2
33367RING, SYNCHRONIZER, NO.1
1ST GEAR SIDE
1ST GEAR SIDE
2ND GEAR SIDE
REVERSE
33368RING, SYNCHRONIZER, NO.2
33371SPRING, SYNCHROMESH SHIFTING KEY, NO.1
33391SPRING, SYNCHROMESH SHIFTING KEY, NO.2
33402GEAR SUB-ASSY, REVERSE IDLER
33402ABUSH OR BEARING (FOR REVERSE IDLER GEAR)
33411ABEARING OR ROLLER(FOR COUNTER GEAR FRONT)
RADIAL BALL BEARING
33411DRING, COUNTER GEAR FRONT BEARING SNAP, NO.1
T=1.07,OD=55.6
33411PBEARING, COUNTERSHAFT CENTER
33411QRING, COUNTER GEAR FRONT BEARING SNAP, NO.2
T=2.10,MARK A,T=2.10 MARK A
T=2.15,MARK B,T=2.15 MARK B
T=2.20,MARK C,T=2.20 MARK C
T=2.25,MARK D,T=2.25 MARK D
T=2.30,MARK E,T=2.30 MARK E
T=2.35,MARK F,T=2.35 MARK F
T=2.10-2.15,T=2.10-2.15
T=2.20-2.25,T=2.20-2.25
T=2.05-2.10,T=2.05-2.10
T=2.15-2.20,T=2.15-2.20
T=2.25-2.30,T=2.25-2.30
T=2.30-2.35,T=2.30-2.35
T=2.35-2.40,T=2.35-2.40
33421GEAR, COUNTER
33451SHAFT, REVERSE IDLER GEAR
33452STOPPER, REVERSE IDLER GEAR SHAFT
33462WASHER, REVERSE IDLER THRUST
33481GEAR, SPEEDOMETER DRIVE (MTM)
N=10,*AXC=T292,SMG R=35:10
N=10,MARK 10X34-36,*AXC=T292,SMG R=35:10
N=6
N=6,MARK 6X18-20,*AXC=T312,SMG R=20:6
N-11
N=10,MARK 10X31-33,*AXC=T312,SMG R=33:10
N=6,MARK 6X21-23
33481AKEY OR BALL, SPEEDOMETER DRIVE GEAR (MTM)
33481BRING OR SPACER (FOR MTM SPEEDOMETER DRIVE GEAR)
T=1.50,OD=31.3
9161140820
main91611-40820
43 parts on this diagram · 9 diagrams in section
TRANSMISSION GEAR (MTM) for Toyota CORONA FR
This section contains 104 genuine Toyota parts for the TRANSMISSION GEAR (MTM) system of the Toyota CORONA FR. Key components include: GEAR SET, REVERSE, RING, HOLE SNAP(FOR REAR BEARING SET), SEPARATOR, MANUAL TRANSMISSION OIL, NO.1, SHAFT, INPUT, BEARING (FOR INPUT SHAFT FRONT).